We had a light practice at the college yesterday (most were away at a competition) and one of the team members asked for help with his bow. I asked him what he was working on and he said his arrow rest. This young man is a Traditional Recurve archer and his rest was a metal wire stick-on rest, designed to be used with a plunger. In fact, shooting without a plunger was damaging his arrows because they were rubbing up against the rest’s bracketry. I suggested he use one of the club’s “loaner” plunger buttons and he set about installing it. I showed him how to adjust it and left him to it. (We learn manual things better by doing than by watching somebody else do it for them.)
When he finished he wanted me to check his installation. The button wasn’t out far enough, it barely protruded from the arrow rest, so I did a quick peek at his centershot and it was way outboard from anywhere good. What the heck? I looked more carefully at the bow (being more focussed before on the student) and noted that the arrow shelf was “crowned,” a design that facilitated shooting arrows off of the shelf. I dropped the arrow onto the shelf and … almost perfect centershot. Even with really skinny arrows, there was no way to shoot off of an elevated arrow rest. The only way I could see that the brass threaded insert could be used would be to bolt on a wrap around arrow rest, that would have to hang back over the edge of the shelf because the bow wasn’t cut with enough of a sight window to place any rest inside the sight window.
Who would make such a bow, I wondered? (I am not telling, and this is not the only one I have seen doing this, just let it be known that the buyer must beware when purchasing archery equipment.)
We did a few other things to allow him to “shoot off of the shelf” which I won’t recount but I happened to take a peek at his arrows. They were 350 spine. At his draw length, he would have needed a 65+# bow to make those arrows work. His bow is 42#. Thankfully, the arrows weren’t cut to his actual draw length and were a couple of inches longer, but they needed to be a couple of inches longer than they were to work in that bow.
Who would sell someone arrows so out of spine like that?
This is a sad tale. In many parts of the country, the number of archery pro shops has dwindled dramatically. I live in Chicago, and if you struck a 50 mile radius circle around where I live, you would have close to 10 million people inside that circle. To the best of my knowledge, there is one full-service archery pro shop in that circle. There are, however, a number of big box sporting goods stores that sell archery gear. Some of the members of one of the archery clubs I belong to work in such stores, so I know there is quality help available but time and again, bizarre sales are made from such stores.
A most common pattern is a newbie target archer goes to such a store and there is someone behind the counter to serve them. They tell the clerk they have a 30# bow and they need arrows. The clerk selects an all-carbon shafted arrow that they are having a special on (!) that is labeled 30#-50#, then measures the archer’s draw length (usually haphazardly) and cuts the arrows to the student’s draw length. This sounds right, no? It is dead wrong.
Many all-carbon arrow manufacturers got into the arrow game by selling a small line of good arrows cheaply enough to get sales. By designing the arrows correctly, they can cover the range of draw lengths that hunters need in maybe three shafts: 30#-50#, 50#-70#, and 70#-90#. With these kinds of shafts, though, you do not cut them to an archer’s draw length, you cut them to the correct spine. If those 30#-50# arrows are to be used on a 30# bow (with a 28˝ draw length), they have to be shot uncut.
Now, my student’s arrows were of a 350 spine, not one of these schemes. The spine chart for these arrows would have him shooting at 65+# at his draw length. There is no way to fit such an arrow to this archer. Either a mistake was made or a retailer was “clearing inventory” by any means at his disposal.
Beginners, intermediate archers, and even some advanced archers do not understand spine charts and all of the criteria needed to fit arrows. They need professional help. I wish there were online programs on how to do this that were easily accessed and easily understood, but there are not. Please do not tell me about YouTube videos, the problem is there are so many videos posted on YouTube that it makes finding the right one quite problematic. I have suggested that major retailers and/or manufacturers set up a YouTube channel to address the equipment needs of these archers but that has not been done. We are currently developing several Internet training programs designed for coaches and archers but those are not yet done. (Maybe by summer.)
The implication for archery coaches is clear, if you want to be helpful, you need to inform yourself on these technical issues so you can be a source of clarity in the sea of confusion that now exists.
BTW I wrote a complete description of how to fit arrows and placed it into the team’s Dropbox folder labeled Instructor Materials. Now if I could just get them to read it!